# Reading a PPF data sheet: what each row means

- Canonical page: https://arkppf.com/guides/reading-a-ppf-data-sheet
- Publisher: ARK PPF (https://arkppf.com/)
- Written for: Paint protection film installers and shops
- Published: 2026-11-15
- Values marked ⟨ … ⟩ are not confirmed yet; ARK PPF does not publish a guess in their place.

## Short answer

A PPF data sheet describes the film layer by layer: its thickness, the base material, the top coat, the temperature at which the top coat heals, how strongly it beads water, how glossy it is and how far it stretches before it breaks. Read each figure with one question: is it measured on this film, or typical of the class?

## Thickness

Quoted in mils, thousandths of an inch. Ask which layers the figure counts: film alone, film and adhesive, or the liner too. Defender: 8.5 mil. [Is thicker film better?](https://arkppf.com/guides/is-thicker-ppf-better)

## Base material: aliphatic or aromatic TPU

The base is the bulk of the film, usually a thermoplastic polyurethane (TPU). The word in front of it names the kind of urethane: aliphatic or aromatic. The two behave differently in sunlight, and a sheet that names one is telling you which chemistry the film is built on. ARK’s base row reads Aliphatic TPU. Thickness and warranty are ARK’s own figures. The other rows are industry-typical values for this class of film, confirmed by ARK for publication, not ARK test results.

How a particular film holds up in sun is a matter of its whole construction, the adhesive and the top coat included, and of measurement over time. ARK publishes no yellowing result yet.

## Top coat

The thin outer layer that carries the surface: gloss or satin, water repellency, stain resistance and self-healing. Fusion’s row reads Ceramic-infused hydrophobic self-healing coat.

## Self-heal activation

The temperature the data sheet gives for the top coat to relax back over a light mark. Light marks close faster the warmer the surface, and more slowly in the cold, which is why sun or a warm rinse helps. The row on ARK’s sheets: 60 °C. It says nothing about deep marks: if you can catch it with a fingernail, it stays.

## Water contact angle

The angle a water droplet makes where it meets the surface. The higher the angle, the rounder the bead and the more readily water rolls off; above 90° a surface is usually called hydrophobic. Fusion, the ceramic gloss film: 105 °. The effect fades with use and comes back with maintenance.

## Gloss at 60°

Measured with a gloss meter at a 60° angle, in gloss units (GU). Higher is shinier; a satin film reads far lower on purpose. Defender: 92 GU. Umbra (a working name), the satin film: 20 GU.

## Elongation at break

How far a sample stretches, as a share of its length, before it breaks. It shows how much the film tolerates on curves, but fitting never goes near that limit: film stretched far enough to whiten is already a stretch mark. Defender: 350%.

## The roll label

The label is the part of the sheet that travels with the film. It should print the film, thickness, finish, warranty, roll size and a lot number. ARK’s standard roll is 60 in × 50 ft. Write the lot on every job record, because a roll traces back to its batch when a claim comes in.

## A data sheet is only as good as its sources

A figure without a test behind it is a claim. Ask which rows are measured on the film itself. ARK says so beside every sheet: Thickness and warranty are ARK’s own figures. The other rows are industry-typical values for this class of film, confirmed by ARK for publication, not ARK test results.

## Films this guide touches

- [ARK Defender](https://arkppf.com/products/defender) (gloss): The thick clear film, for the driver asking how much stone a hood can take before it chips.
- [ARK Fusion](https://arkppf.com/products/fusion) (ceramic gloss): Clear gloss film with the water-repellent layer in its own top coat, for the buyer weighing film plus a separate coating.
- [ARK Umbra](https://arkppf.com/products/umbra) (satin): Satin film for two buyers: the one who wants gloss paint turned satin, and the one whose factory matte paint cannot be colour-matched or polished.
- [ARK Spectrum](https://arkppf.com/products/spectrum) (colour): Colour film for the buyer choosing between a vinyl wrap and a change of colour that also protects the paint. It is not the answer to a clear-film question.

## Read next

- [Is thicker film better? What mil ratings mean](https://arkppf.com/guides/is-thicker-ppf-better)
- [Does paint protection film turn yellow?](https://arkppf.com/guides/does-paint-protection-film-turn-yellow)
