# Cutting PPF rolls on your own plotter and software

- Canonical page: https://arkppf.com/guides/cutting-ark-film-on-your-own-plotter
- Publisher: ARK PPF (https://arkppf.com/)
- Written for: Paint protection film installers and shops
- Published: 2026-10-04
- Last updated: 2026-11-14
- Values marked ⟨ … ⟩ are not confirmed yet; ARK PPF does not publish a guess in their place.

## Short answer

ARK has no in-house cutting software. Most shops buy ARK paint protection film by the roll and cut it on the plotter and pattern software they already run. Pre-cut kits are available too. The cut spec, meaning backing thickness, blade depth and offset, is published as a starting setting to confirm with a test cut.

## How shops cut ARK

ARK has no in-house cutting software and no pattern platform of its own. Most of what ARK sells is rolls to professional install shops, and those shops cut the film on the plotter and the pattern software they already own.

The position on the cut spec is one line: bring your own platform.

## Do you need the film brand’s own pattern software?

Not for ARK. Some film brands pair their film with a pattern platform of their own. ARK has none, so the film is not tied to any software. You keep the plotter, the pattern library and the workflow you have. Adding ARK does not mean opening a new software account or retraining anyone on a new cutting tool.

It also means there is no ARK pattern library to lean on. The patterns are your software’s, and any adjustment for the film is yours, made from your own test cuts.

## Plotter settings for PPF: liner, blade and offset

The cut spec is the set of values a plotter needs for a film. The backing comes first, because the liner is the layer the blade must stop at. The values below are starting settings for a film of this thickness. Confirm them with a test cut, because blades and plotters differ.

- Backing (liner) thickness: 3 mil (75 µm) PET liner.
- Blade depth: 45° blade, through film and adhesive, scoring the liner only.
- Offset: 0.25 mm.

## Before you cut a full job

The one figure printed on the roll is the film’s thickness: 8.5 mil for Defender. Start from the settings you use for film of that thickness, then prove them on an offcut.

- Cut a small test piece with tight corners and narrow relief cuts.
- Check the blade has gone through the film and adhesive and has only marked the liner.
- Weed it. Clean corners and no tearing mean the settings hold.
- Note the lot number from the roll label on the job record, so a roll traces back to its batch.

## Pre-cut kits or bulk rolls?

ARK sells mainly rolls to shops, which cut them on their own plotter and software, and offers pre-cut kits as well. A kit arrives cut, which suits a shop that would rather not cut a particular job itself. A roll is cut to whatever the job needs.

Tell ARK the work your shop does, and a person replies about rolls, kits and becoming an authorized dealer. [See the installer page](https://arkppf.com/installers).

- Rolls suit a shop with a plotter and pattern software, a steady flow of work, and jobs that vary from car to car.
- Pre-cut kits suit a shop without a plotter, a job it rarely cuts, or a week when the plotter is busy.

## No platform recommended

ARK does not name or recommend a pattern platform. The right one is the one your shop already cuts well with.

## These are starting settings, not your settings

The cut spec is where to start for a film of this thickness, not a setting proven on your plotter. Blades wear and plotters differ, so prove the numbers on an offcut before a customer’s job. A setting copied without a test cut and run into a customer’s bumper is worse than none.

## Films this guide touches

- [ARK Defender](https://arkppf.com/products/defender) (gloss): The thick clear film, for the driver asking how much stone a hood can take before it chips.

## Read next

- [Is thicker film better? What mil ratings mean](https://arkppf.com/guides/is-thicker-ppf-better)
- [Film defect or install defect? How to tell what went wrong](https://arkppf.com/guides/film-defect-or-install-defect)
